установить на домашней странице | добавить в коллекции
По-китайски | По-английски | русский
новости
предприятия новости
новости професии
техническая документация
добавить отзыв
свяжите с нами

Tel:+86-0755-23699550   

Fax:+86-0755-23699531
Email:  info@szzest.com
Website:www.szzest.com
ADD:3rd Floor 2nd Bld Xinfengze

 industrial park Shangnan East

 Road Shajing street Bao'an 

district Shenzhen China 518125


новости
  предприятия новости
Что такой canbus?
публикация:admin  время:2013/10/8 16:46:53   просмотр:2872次
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Controller–area network (CAN or CAN-bus) is a vehicle bus standard designed to allow microcontrollers and devices to communicate with each other within a vehicle without a host computer.

CAN is a message-based protocol, designed specifically for automotive applications but now also used in other areas such as industrial automation and medical equipment.

Development of the CAN-bus started originally in 1983 at Robert Bosch GmbH.[1] The protocol was officially released in 1986 at the Society of Automotive Engineers (SAE) congress in DetroitMichigan. The first CAN controller chips, produced by Intel and Philips, came on the market in 1987. Bosch published the CAN 2.0 specification in 1991.

CAN is one of five protocols used in the OBD-II vehicle diagnostics standard. The OBD-II standard has been mandatory for all cars and light trucks sold in the United States since 1996, and the EOBD standard has been mandatory for all petrol vehicles sold in the European Union since 2001 and all diesel vehicles since 2004.[2]

Applications

Automotive

A modern automobile may have as many as 70 electronic control units (ECU) for various subsystems.[3] Typically the biggest processor is the engine control unit (also engine control module/ECM or Powertrain Control Module/PCM in automobiles); others are used for transmissionairbagsantilock braking/ABScruise controlelectric power steering/EPS, audio systems, windows, doors, mirror adjustment, etc. Some of these form independent subsystems, but communications among others are essential. A subsystem may need to control actuators or receive feedback from sensors. The CAN standard was devised to fill this need.

The CAN bus may be used in vehicles to connect engine control unit and transmission, or (on a different bus) to connect the door locks, climate control, seat control, etc. Today the CAN bus is also used as a fieldbus in general automation environments, primarily due to the low cost of some CAN Controllers and processors.

Bosch holds patents on the technology, and manufacturers of CAN-compatible microprocessors pay license fees to Bosch, which are normally passed on to the customer in the price of the chip. Manufacturers of products with custom ASICs orFPGAs containing CAN-compatible modules may need to pay a fee for the CAN Protocol License.

Technology

CAN is a multi-master broadcast serial bus standard for connecting electronic control units (ECUs).

Each node is able to send and receive messages, but not simultaneously. A message consists primarily of an id (identifier), which represents the priority of the message, and up to eight data bytes. It is transmitted serially onto the bus. This signal pattern is encoded in non-return-to-zero (NRZ) and is sensed by all nodes.

The devices that are connected by a CAN network are typically sensorsactuators, and other control devices. These devices are not connected directly to the bus, but through a host processor and a CAN controller.

If the bus is free, any node may begin to transmit. If two or more nodes begin sending messages at the same time, the message with the more dominant id (which has more dominant bits, i.e., zeroes) will overwrite other nodes' less dominant id's, so that eventually (after this arbitration on the id.) only the dominant message remains and is received by all nodes. This mechanism is referred to as priority based bus arbitration. Messages with numerically smaller values of id. have higher priority and are transmitted first.

Each node requires a

  • Host processor
    • The host processor decides what received messages mean and which messages it wants to transmit itself.
    • Sensors, actuators and control devices can be connected to the host processor.
  • CAN controller (hardware with a synchronous clock).
    • Receiving: the CAN controller stores received bits serially from the bus until an entire message is available, which can then be fetched by the host processor (usually after the CAN controller has triggered an interrupt).
    • Sending: the host processor stores its transmit messages to a CAN controller, which transmits the bits serially onto the bus.
  • Transceiver
    • Receiving: it adapts signal levels from the bus to levels that the CAN controller expects and has protective circuitry that protects the CAN controller.
    • Transmitting: it converts the transmit-bit signal received from the CAN controller into a signal that is sent onto the bus.

Bit rates up to 1 Mbit/s are possible at network lengths below 40 m. Decreasing the bit rate allows longer network distances (e.g., 500 m at 125 kbit/s).

The CAN data link layer protocol is standardized in ISO 11898-1 (2003). This standard describes mainly the data link layer(composed of the logical link control (LLC) sublayer and the media access control (MAC) sublayer) and some aspects of thephysical layer of the OSI reference model. All the other protocol layers are the network designer's choice.

Data transmission

CAN features an automatic arbitration-free transmission. A CAN message that is transmitted with highest priority will succeed, and the node transmitting the lower priority message will sense this and back off and wait.

This is achieved by CAN transmitting data through a binary model of "dominant" bits and "recessive" bits where dominant is a logical 0 and recessive is a logical 1. This means open collector, or wired or physical implementation of the bus (but since dominant is 0 this is sometimes referred to as wired and). If one node transmits a dominant bit and another node transmits a recessive bit then the dominant bit "wins" (a logical AND between the two).

вверхняя страница:автомобильный dvd переоснащение несколько вариант.
следуюшая страница:Компания ZEST -создание ценности
 соединение дружба: Golden supplier Alibaba International | Golden supplier Alibaba International 2 | Golden supplier Alibaba Domestic | Global Sources |

SHENZHEN ZEST TECHNOLOGY CO.,LTD  版权所有   粤ICP备13071219号-1

3rd Floor 2nd Bld Xinfengze industrial park Shangnan East Road Shajing street Bao'an district Shenzhen China

Tel:+86-0755-23699550   Fax:+86-0755-23699531   Email:  info@szzest.com



 粤ICP备13071219号-1